Plasma Cutter Tig

PowerPro 205S 200AMP ACDC TIG ARC PULSE WELDER 50amp plasma cutter by EVERLAST

PowerPro 205S 200AMP ACDC TIG ARC PULSE WELDER 50amp plasma cutter by EVERLAST
PowerPro 205S 200AMP ACDC TIG ARC PULSE WELDER 50amp plasma cutter by EVERLAST
PowerPro 205S 200AMP ACDC TIG ARC PULSE WELDER 50amp plasma cutter by EVERLAST

PowerPro 205S 200AMP ACDC TIG ARC PULSE WELDER 50amp plasma cutter by EVERLAST

Looking for a good all around welder with some extra features? The IGBT inverter-based PowerPRO 205S from Everlast is designed to be just that unit. With 200 amp TIG, 160 amp Stick and 50 amp Plasma cutter capabilities, the unit is an all-in-one solution that is useful in many situations where space and portability are key concerns.

The flexibility and versatility that the multi-process PowerPro 205S offers is hard to beat. Stable arc performance helps both hobbyists and professionals to make quality repairs in about any situation. The pulse capability further extends the unit's capabilites, as well as the fully adjustable AC Frequency and AC balance while operating in TIG mode. The PowerPRO multi-units are definitely the utility players in Everlast's lineup and are ready to go to work anywhere they are needed. Compact IGBT Inverter design and low power consumption is ideal for portable use. Compact, yet powerful TIG welding/Plasma cutting features. Easy to use controls with simple selector switch for process changeover. Quick change out of torches for easy change from TIG to plasma back to TIG. Good duty cycle ratings for TIG, Stick, and Plasma. Duty Cycle indicator warns when thermal threshold has been exceeded and interrupts welding/cutting output until condition is resolved.

Over Current indicator warns when duty cycle has been exceeded and interrupts welding/cutting output until condition is resolved. OK to cut indicator lights up when air pressure meets minimum required operating pressure and interrupts cutting output when air pressure is too low. Low dross cuts on steel up to 5/8" with up to 7/8" maximum capacity (under ideal conditions).

Exceptional arc stability for TIG/Stick functions. Everlast 26-Series air-cooled TIG torch with DINSE-style 35 series connector. Stick electrode holder with 10 ft cable and DINSE-style 35 series connector. Everlast S-45 Plasma torch with DINSE-style 35 series connector. Work clamp with 10 ft.

Cable and DINSE-style 25 series connector. Air Pressure regulator with water trap/filter Note: This is not an air dryer. A separate, inline air dryer, supplied by the customer should be installed. Consumable starter kit for TIG and Plasma (Does not include TIG tungsten). Everlast air-cooled Series 9F flex neck TIG torch for delicate, lower amp work.

Everlast water-cooled Series 20F flex neck TIG torch for higher amperage work. C-K Trimline air cooled flexneck 26 with superflex cable, safe-loc connector, and stubby gas lens kit (recommended). C-K FL 150 Flex-loc air cooled torch with superflex cable, safe-loc connector, and stubby gas lens kit. 12.5 ft C-K FL 250 Flex-loc water-cooled torch with superflex cable, safe-loc connector, and stubby gas lens kit. Farm/Ranch where portable repairs are needed and carrying multiple units is not an option.

Motorsports/At the track/Offroad where quick repairs are often needed. For businesses that often need spot repairs and one-off projects completed. A separate Air Dyer must be used inline while plasma cutting.

To change from TIG to Plasma operation, both the input gas supply, regulator and the torches must be swapped over. Only one torch can be connected at any given time.

Remember: The TIG and plasma torch are always connected to the negative terminal. Generally, the Stick holder is connected to the positive terminal for most welding electrodes. For best results, a higher output generator may be required. Plasma Cutting capability with dry air, new consumables, proper air pressure etc. Quality and capacity of cut depends upon consumable orifice size, standoff height, travel speed, etc. If there is damage, we can help file a damage claim immediately. These packages will be refused and sent back to YOU at your cost. We will do our best to expedite backordered items as soon as possible. 3- Please provide a physical address. The item "PowerPro 205S 200AMP ACDC TIG ARC PULSE WELDER 50amp plasma cutter by EVERLAST" is in sale since Monday, May 7, 2018.

This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\Multiprocess Welders & Cutters". The seller is "fox_merchand" and is located in Daly City, California. This item can be shipped to United States.

  • Power Source: 220/240V 1 phase
  • Current: 1 Phase
  • Model: PP205SI-NOVA
  • MPN: PP205SI-NOVA
  • Brand: Everlast
  • Multi-Process: Yes
  • Processes: Plasma, AC/DC TIG, Arc


PowerPro 205S 200AMP ACDC TIG ARC PULSE WELDER 50amp plasma cutter by EVERLAST